Do It Yourself Bathtub Setup.
Do It Yourself Bathtub Setup.
Blog Article
We've uncovered this article about Installing A Bathtub below on the web and reckoned it made sense to share it with you over here.
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Installing a bathtub isn't exactly rocket science, however it does need strong plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bathtub with a brand-new one is also a moderately challenging project. If the old tub is easily available, the job can relocate immediately; if you need to open up a wall surface to eliminate the old bathtub as well as place the brand-new tub, the job is a lot harder. In either case, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub and also embeded in the brand-new one. See to it you have actually qualified yourself for the task and are comfortable attempting it. Rather than hiring a contractor to take control of a halfway-completed task, it is far better to take into consideration utilizing one prior to you begin. Chances are you may need a specialist plumber to make tube links.
This post will help you install a brand-new tub in your restroom if you have already acquired a brand-new tub and also do not require to alter the arrangement of your previous water supply pipelines.
Your devices as well as material list need to make up the following:
Preparing for the Setup
First of all, the supporting structure provided with the bath needs to be fitted (if needed) according to the manufacturer's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to make sure that if the tap comes with a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bathroom, it is likewise sensible to fit a sustaining plate under the taps unit to stop strain on the bath tub.
Fit the versatile tap adapters to the bottom of the two faucets utilizing 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the outlet via the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste outlet on the bath tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be suited its last position.
Removing Old Taps
If you need to replace old faucets with brand-new ones as a part of your installment, after that the first thing you should do is disconnect the water system. After doing so, switch on the taps to drain any type of water staying in the system. The procedure of eliminating the existing taps can be rather troublesome because of the restricted access that is typically the instance.
Use a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipes to the taps. Have a cloth prepared for the staying water that will originate from the pipelines. As soon as the supply pipelines have actually been removed, use the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this procedure. As soon as the taps have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing compound.
Before carrying on to fit the new taps, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Installing the Bathtub
Using the two wooden boards under its feet, place the tub in the needed setting. The wood boards are handy in equally spreading out the weight of the bath tub over the location of the boards as opposed to focusing all the weight onto four small points.
The next objective is to make certain that the tub is leveled all round. This can be accomplished by inspecting the spirit level and adjusting the feet on the bathtub till the level checks out level.
To install taps, fit all-time low of the outermost versatile tap connector to the appropriate supply pipeline by making a compression sign up with; then do the same for the various other faucet.
Turn on the supply of water and examine all joints and also new pipework for leaks and tighten them if essential. Fill up the tub as well as also check the overflow electrical outlet and also the regular electrical outlet for leaks.
Finally, fix the bath paneling as defined in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait until the tub has actually been made use of a minimum of once as this will certainly resolve it right into its final position.
Suitable New Touches
If the tails of the new taps are plastic, after that you will certainly need a plastic connector to stop damages to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end offers a connection to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly call for decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, place the tap in the placing opening in the bath/basin guaranteeing that the washers remain in location between the faucet as well as the sink. Secure the faucet in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the taps. The faucets can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind ought to be connected to the faucet ends initially, tightening just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is required to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to fracture a rigid seal, triggering the water to penetrate the wall in between the bathroom and also the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as installations. They are marketed in tubes and cartridges, as well as can sealing spaces up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of drenched paper or soft rope. Remember to always load the bathtub with water before securing, to permit the movement experienced when the bathtub remains in use. The sealant can fracture fairly very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are also quickly readily available on the market. It is recommended to fit the ceramic tiles making use of water-resistant or water resistant sticky and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a serious reader about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround, I think sharing that piece of content was really helpful. Be sure to take a moment to promote this blog entry if you liked it. I enjoy reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Or Book Technician Here Report this page